Automatic Braking System

There has been a tremendous growth these days in the areas of design, internal and external features, the engine, transmission, safety etc. There have been advancements in the braking systems in recent times. When you go to buy a new car, you have to ask the salesman about a particular feature called the automatic braking system. Let me tell you a few things about this feature.
This type uses brakes and sensors together to reduce the speed of the car. In some car models, you will find that the brakes are applied without any input from the driver whereas in others they provide braking assistance to the driver.

Let's understand how do they work. They depend on the input from the sensors which may be lasers, radar or even video data. It uses this data to determine if there are any objects on the path of the car. If it detects any object, it determines the speed of the object. Now if the speed of the object is greater by some amount, then there is likely to be a collision and it activates the braking system. If the car has accurate GPS systems, then it can activate the auto brakes when the driver fails to stop on time. Now, you will ask a very obvious question that is it necessary? If you drive carefully, then probably you will not know about the auto brakes in your car.
There will be no change in the pattern of driving with or without auto brakes. Some recent models have automatic braking system such as the 2016 Chrysler 300, 2016 Honda Civic, 2016 Subaru Impreza and many more.


 



















This is just a technology that is used to aid and abet the driver to avoid collisions and reduce property damage.

Comments

Post a Comment

Popular posts from this blog

3 spool vs 2 spool

Image
In the Trent 1000, there is 3 spool arrangement of compressors and turbines. This means that there are three sets of compressors and turbines which are connected by three separate shafts. They are the low pressure compressor (LPC) which is the fan and turbine (LPT), Intermediate pressure compressor (IPC) and turbine (IPT) and high pressure compressor (HPC) and turbine (HPT). This is on contrast to the two spool arrangement currently used in many aircrafts where a LPC/LPT and HPC/HPT are used only. All the three shafts are located within each other. The fan positioned at the front of the engine is run by the LPT via a gearbox so that it can operate at optimum speeds. Since the large diameter fan requires a large torque to start rotating, it limits the high speed attained by the LPT due to which its efficiency decreases. Additions of an additional set of compressor and turbine eliminates the influence of this problem but does not eliminate the problem itself! The problem is elim
Keep reading

Materials used in Turbine blades

Image
There has been a wide range of materials used for the manufacturing of gas turbine blades. It is one of the most important parts in a gas turbine and any deterioration of it will affect the performance and efficiency of the turbine and most importantly will damage the turbine.  Many materials have been tested and used but the most preferred materials include steel, titanium, Nickel based super alloys and ceramics. The first stage of the compressor is very delicate as it is subjected to a very high temperature of approx. 1400-1500 degree celsius.  This part of the turbine should tolerate high temperatures, high pressures, high thermal stresses including creep and fatigue, vibrations which can influence it's performance. The first stage uses Udimet 500, Nickel based super alloy Inconel 738 or GTD 111.  The relatively cold stages of the turbine employ titanium as there are chances of it igniting when used above 500 degree celsius.        Applications                
Keep reading

Can 3D Printing take over the World?

3D Printing is now one of he most discussed subjects in the modern world with its field offering us untapped potential for the future manufacturing and construction applications. Its almost as if everyday you hear a new story regarding any advancement in this field. Its applications are so diverse that you can find its use in almost any major industry. Automobile?, Sanitary?, Construction? You name it. Hell you can find its use in the medical industry as well. Within a decade or probably lesser than a decade, you will notice that the  3D printed ABS/PLA/PC models of human organs have replaced the aged and tattered PVC models. It is only a matter of time after which 3d printing will be the most discussed and developed fields among the younger generation due to the immense opportunities it will provide. Please do share your views and any ideas if any related to 3d printing. 
Keep reading