Manufacturing of Tires

Today I'll give you short intro of how the tires are manufactured. We have seen different brands such as Michelin, Dunlop, Bridgestone, Continental and may more. 

The manufacturing of a tire is very complex just like a smartphone. The main ingredients used are natural rubber, synthetic rubber, silica, carbon black and many chemical substances.


1.  First, all these ingredients are mixed in a giant blender to get a black compound which is the basis of the tire material. 
2. Next they are then cut into individual strips for every tire manufactured. Here all the other elements required for a tire such as beads, belt, shoulder are all prepared.
 3. The next stage is the assembly of all these components in an individual tire. The tire which is developed in this stage is called green tire. 
4. This green tire is then sent for vulcanization where many synthetic components are added to increase the durability of the tire. The pattern is also created on the tire. 
5. The last stage is inspection where quality workers check the tires for any internal weaknesses. In some cases simulation is done in order to double check the safety and durability of the tire. 

We can tell with some basic knowledge that the tire industry is the largest consumer of natural rubber in the rate of millions. Maybe the consumption might reach billions within a few years.

Comments

Post a Comment

Popular posts from this blog

Materials used in Turbine blades

Image
There has been a wide range of materials used for the manufacturing of gas turbine blades. It is one of the most important parts in a gas turbine and any deterioration of it will affect the performance and efficiency of the turbine and most importantly will damage the turbine.  Many materials have been tested and used but the most preferred materials include steel, titanium, Nickel based super alloys and ceramics. The first stage of the compressor is very delicate as it is subjected to a very high temperature of approx. 1400-1500 degree celsius.  This part of the turbine should tolerate high temperatures, high pressures, high thermal stresses including creep and fatigue, vibrations which can influence it's performance. The first stage uses Udimet 500, Nickel based super alloy Inconel 738 or GTD 111.  The relatively cold stages of the turbine employ titanium as there are chances of it igniting when used above 500 degree celsius.      ...
Keep reading

Self Energizing Brakes

Image
The usual drum brakes in our car are provided with a remarkable feature called 'servo' or 'self energizing' feature. It is this feature that is responsible for the smooth and flat application of brakes in automobiles. When the vehicle is moving left, in the forward direction, then the drum will rotate in the anticlockwise direction. When the brake pedal is suddenly pressed, the two brake shoes at the drum will have full contact with the drum. However, one of the brake shoes, the primary brake shoe tends to slip for a certain distance in the drum's direction. Due to this, the primary brake shoe will tend to apply a rearwards force on the secondary brake shoe at the bottom. The wheel cylinder at the top forces the piston against the top of both the brake shoes. Due to this, the secondary brake shoe experiences force on both the sides i.e the top and bottom side.  This ensures that the brakes are applied uniformly and much less effort is applied.
Keep reading

3 spool vs 2 spool

Image
In the Trent 1000, there is 3 spool arrangement of compressors and turbines. This means that there are three sets of compressors and turbines which are connected by three separate shafts. They are the low pressure compressor (LPC) which is the fan and turbine (LPT), Intermediate pressure compressor (IPC) and turbine (IPT) and high pressure compressor (HPC) and turbine (HPT). This is on contrast to the two spool arrangement currently used in many aircrafts where a LPC/LPT and HPC/HPT are used only. All the three shafts are located within each other. The fan positioned at the front of the engine is run by the LPT via a gearbox so that it can operate at optimum speeds. Since the large diameter fan requires a large torque to start rotating, it limits the high speed attained by the LPT due to which its efficiency decreases. Additions of an additional set of compressor and turbine eliminates the influence of this problem but does not eliminate the problem itself! The problem is elim...
Keep reading